The main area of a home in Etobicoke that can let in air from outside into your home is your attic. This is also the main place where insects and animals can infest without you noticing before it is too late. The best to prevent both of these problems is to have the proper sealing done in your attic. This will mainly involve insulating the entire area properly with the most advanced method of insulation that is available right now. The following is the best option of insulation for any type house that has an attic:
CozyGuYYZ: Professional Home Insulation Contractors In Etobicoke
Foam insulation is a new type of insulation being used a lot in Etobicoke that many builders and homeowners alike are beginning to use in replacement of lay-in insulation. Instead of stapling pieces of fiberglass-based traditional insulation, this type is completely sprayed onto the area which guarantees complete coverage. This is also very helpful when it comes to tight spaces that are hard to get to.
Questions to Ask When Selecting a Spray Foam Insulation Contractor
I have just completed an addition to my house. I've heard that blown in insulation is better than batts since covers the joists completely and leaves no open areas. Do you have any do it yourself suggestions?
Yes you are correct. Blown in insulation is better that batts when installed properly as it does seal the attic better.
First you need to measure your attic area that you plan on insulating. Most attics require a value of R-30, R-38 or R-49, depending on your climate and location. Once you know the square footage of your attic you can determine how much insulation you'll need by simple looking on the chart located on the bag of insulation.
Before you get started you will need to determine what materials you will need. Assuming your home has recessed lights, ceiling and bathroom fans and eave vents you will need the following tools and materials:
Loose Fill Insulation
Staple Hammer and Staples
Insulation Blowing Machine (Available at your local rental store)
I've found blowing insulation into the attic is a simple process. Start and the far ends of the attic. Going back and forth make sure its level and smooth. Make sure to get all areas of the attic and don't fill any vents or recessed light areas. Take a tape measure with you and check the levels once in a while. As an example, if your installing an R-38 of fiberglass insulation you would want it to measure 16 inches deep. As you work your way back near the attic access make sure your helper is getting that excess hose out of the way. When you get to about 6 feet from the access hole stop the machine so you can get on the ladder. Once on the ladder finish installing, making sure to bring the level evenly against the dam you previously built.
The final step is to place a piece of batt insulation in the access hole and carefully put the attic hole lid back into place. Now your done! Stay out of that attic as much as possible from this point as loose fill insulation that has been stepped on or crushed looses it's R value.
Home Insulation - Is It Cold Outside?
Each and every home needs proper insulation, this is a fact. Fortunately, these days, it is a lot easier to find the proper material that would best fit the home's specific needs. After all, every house differs in terms of layout and need for heating. But first, let's talk about insulation. If your home is properly insulated, the heat flow to and out of your home is greatly reduced. This means that you need not use up too much energy in the colder months just to keep your home warm. Insulation is added to various areas in your home such as in between walls and even floors in order to make this happen. Of course, the material used also plays quite a significant role in making sure that the heat does not escape and as such, choosing the right one for your house is imperative.
2. Foam boards or rigid foam - These are commonly used to insulate the house's foundation because of the fact that it is resistant to water.
3. Liquid foam - A thin layer of this would be spread onto a wall and the left to expand and fill the cavity where it was applied before anything can be added on top.
So there you have it, the top 3 most common insulation materials for your home.
- Crawl Space Insulation Contractors Etobicoke, Ontario |
- House Insulation Contractors Smithfield, Ontario |
- Roof Insulation Company Rexdale, Ontario |
- Interior Wall Insulation Contractors Islington, Ontario |
- Loft Insulation Contractor Mimico, Ontario |
- Exterior Wall Insulation Contractors Long Branch, Ontario |
- Basement Insulation Companies Markland Wood, Ontario |
- Loft Insulation Company Eatonville, Ontario |
- Basement Wall Insulation Companies Sunnylea, Ontario |
- Roof Insulation Contractor Humber Bay, Ontario |
- Loft Insulation Contractors Richview, Ontario |
- Garage Insulation Contractor Eringate, Ontario |
- Garage Insulation Company West Deane, Ontario |