Markham Insulation Removal Company

The main area of a home in Markham  that can let in air from outside into your home is your attic. This is also the main place where insects and animals can infest without you noticing before it is too late. The best to prevent both of these problems is to have the proper sealing done in your attic. This will mainly involve insulating the entire area properly with the most advanced method of insulation that is available right now. The following is the best option of insulation for any type house that has an attic:

Types Of Attic Insulation

CozyGuYYZ: Professional Attic Insulation Company In Markham

Foam insulation is a new type of insulation being used a lot in Markham  that many builders and homeowners alike are beginning to use in replacement of lay-in insulation. Instead of stapling pieces of fiberglass-based traditional insulation, this type is completely sprayed onto the area which guarantees complete coverage. This is also very helpful when it comes to tight spaces that are hard to get to.

Home Insulation - Is It Cold Outside?

Commercial Building Insulation

Attic insulation is used for maintaining an equitable temperature within a house. Being the hottest part of every home, it is placed on the top of the building. Also, the excess temperature inside the attic can actually hinder the normal functioning of the central air conditioning system of the building. The situation will lead to consumption of more energy and thus, a mounting electricity bill.

Why Attic Insulation?
It is mainly used because the insulation provides the flow of heat to other important parts of the room and solely calculated on the measurement of R-value. The concept is R-value is based on determining the intensity of thermal resistance which is offered by the insulator. The selection of the insulator is chosen for its high level of R-value that further signifies greater resistance to the way to heat. Install it at home or anywhere else, if you know the right procedure to the installation process. Read on to know more about the installation of attic insulation.

Basically, it can be divided into three categories; fiberglass batt insulation, spray form insulation and cellulose attic insulation. Installing a fiberglass batt option, you need to call experts and it costs more than the other two options. Spray form is mainly popular for its commercial uses it has high R-value. Cellulose attic insulation is comparatively easy process that can be done by DIY process or by experts.

Attic Insulation!

Roof And Wall Insulation

Scenario:

I have just completed an addition to my house. I've heard that blown in insulation is better than batts since covers the joists completely and leaves no open areas. Do you have any do it yourself suggestions?

Solution:

Yes you are correct. Blown in insulation is better that batts when installed properly as it does seal the attic better.

First you need to measure your attic area that you plan on insulating. Most attics require a value of R-30, R-38 or R-49, depending on your climate and location. Once you know the square footage of your attic you can determine how much insulation you'll need by simple looking on the chart located on the bag of insulation.

Before you get started you will need to determine what materials you will need. Assuming your home has recessed lights, ceiling and bathroom fans and eave vents you will need the following tools and materials:

Loose Fill Insulation

Cardboard Baffles

Flashing

Duct Tape

Staple Hammer and Staples

Utility Knife

Ladder

Insulation Blowing Machine (Available at your local rental store)

I've found blowing insulation into the attic is a simple process. Start and the far ends of the attic. Going back and forth make sure its level and smooth. Make sure to get all areas of the attic and don't fill any vents or recessed light areas. Take a tape measure with you and check the levels once in a while. As an example, if your installing an R-38 of fiberglass insulation you would want it to measure 16 inches deep. As you work your way back near the attic access make sure your helper is getting that excess hose out of the way. When you get to about 6 feet from the access hole stop the machine so you can get on the ladder. Once on the ladder finish installing, making sure to bring the level evenly against the dam you previously built.

The final step is to place a piece of batt insulation in the access hole and carefully put the attic hole lid back into place. Now your done! Stay out of that attic as much as possible from this point as loose fill insulation that has been stepped on or crushed looses it's R value.

 


HomePage