Basement Insulation Contractors Greensborough, Ontario |

Most of the energy costs spent to keep a Greensborough home warm in the winter and cool in the summer end up leaving through the attic. In the summer, the sun’s heat pours in through the attic and in the winter, warm air rises past the ceiling and out of the home. Saving on energy costs starts in the attic, but how much insulation is enough?

Are You Trying To Find Insulation Removal Contractors For Your Greensborough House?

Although spray foam insulation as we know it today truly emerged in the 1980s around the Greensborough area, spray foam actually has its roots several decades further in the past, beginning with the development of polyurethane foam in the 1940s by Otto Bayer. Otto Bayer, an industrial chemist, actually began working with polyurethane in Germany during the late 1930s. This technology was brought to the United States in the early 1940s by David Eynon, the president of Mobay, a war effort conglomerate created from the partnering of two chemical industry giants, Monsanto and the Bayer Corporation.

Spray Foam Insulation - Open and Closed Cell

Roll Out Insulation For Attic

Scenario:

I have just completed an addition to my house. I've heard that blown in insulation is better than batts since covers the joists completely and leaves no open areas. Do you have any do it yourself suggestions?

Solution:

Yes you are correct. Blown in insulation is better that batts when installed properly as it does seal the attic better.

First you need to measure your attic area that you plan on insulating. Most attics require a value of R-30, R-38 or R-49, depending on your climate and location. Once you know the square footage of your attic you can determine how much insulation you'll need by simple looking on the chart located on the bag of insulation.

Before you get started you will need to determine what materials you will need. Assuming your home has recessed lights, ceiling and bathroom fans and eave vents you will need the following tools and materials:

Loose Fill Insulation

Cardboard Baffles

Flashing

Duct Tape

Staple Hammer and Staples

Utility Knife

Ladder

Insulation Blowing Machine (Available at your local rental store)

I've found blowing insulation into the attic is a simple process. Start and the far ends of the attic. Going back and forth make sure its level and smooth. Make sure to get all areas of the attic and don't fill any vents or recessed light areas. Take a tape measure with you and check the levels once in a while. As an example, if your installing an R-38 of fiberglass insulation you would want it to measure 16 inches deep. As you work your way back near the attic access make sure your helper is getting that excess hose out of the way. When you get to about 6 feet from the access hole stop the machine so you can get on the ladder. Once on the ladder finish installing, making sure to bring the level evenly against the dam you previously built.

The final step is to place a piece of batt insulation in the access hole and carefully put the attic hole lid back into place. Now your done! Stay out of that attic as much as possible from this point as loose fill insulation that has been stepped on or crushed looses it's R value.

Spray Foam Equipment That You Will Need

Movement of air in and out of a home can be a leading cause of escalated energy bills. Air can enter your house through holes, cracks and crevices. You can stop unconditioned air from entering your home and indoor conditioned air from escaping outside by adding an advanced insulation system to achieve optimal building performance.

Under House Insulation

A number of companies are offering DIY polyurethane foam insulation kits for home use. TigerFoam, Handi Foam from FomoFoam, Foam It Green DIY Kits are some of the top brands available online. Tiger Foam offers both Slow Rise and Fast Rise formulations. The Slow Rise is for filling wall cavities and other hidden closed-off spaces in the house. The Fast Rise foam is more suitable for spraying surfaces.

The DIY kits come complete with all the equipment needed to apply the spray foam-nozzles, tank, hose and tips. They also have careful step-by-step instructions that need to be followed in order to the job safely and also for best results.

Apart from insulation the polyurethane foam also acts as a sound barrier. It is moisture resistant and hence prevents mold in the wall cavities and wall surfaces. The excellent insulation capacity of the foam results in the complete cut-off of air transfer from and into the house. Retention of temperature of the house is excellent in homes insulated using polyurethane foam insulation kits. You will save a ton of money in utility bills and the insulation costs will soon paid for.


http://cozyguyyz.pro/markham/

Insulation Removal Contractors Services By CozyGuYYZ