Radiant Barrier Insulation Companies Agincourt, Ontario |

Most of the energy costs spent to keep a Agincourt home warm in the winter and cool in the summer end up leaving through the attic. In the summer, the sun’s heat pours in through the attic and in the winter, warm air rises past the ceiling and out of the home. Saving on energy costs starts in the attic, but how much insulation is enough?

Are You Trying To Find Ceiling Insulation Companies For Your Agincourt House?

Although spray foam insulation as we know it today truly emerged in the 1980s around the Agincourt area, spray foam actually has its roots several decades further in the past, beginning with the development of polyurethane foam in the 1940s by Otto Bayer. Otto Bayer, an industrial chemist, actually began working with polyurethane in Germany during the late 1930s. This technology was brought to the United States in the early 1940s by David Eynon, the president of Mobay, a war effort conglomerate created from the partnering of two chemical industry giants, Monsanto and the Bayer Corporation.

How To Install Blown In Attic Insulation

Insulating Attic Walls

Scenario:

I have just completed an addition to my house. I've heard that blown in insulation is better than batts since covers the joists completely and leaves no open areas. Do you have any do it yourself suggestions?

Solution:

Yes you are correct. Blown in insulation is better that batts when installed properly as it does seal the attic better.

First you need to measure your attic area that you plan on insulating. Most attics require a value of R-30, R-38 or R-49, depending on your climate and location. Once you know the square footage of your attic you can determine how much insulation you'll need by simple looking on the chart located on the bag of insulation.

Before you get started you will need to determine what materials you will need. Assuming your home has recessed lights, ceiling and bathroom fans and eave vents you will need the following tools and materials:

Loose Fill Insulation

Cardboard Baffles

Flashing

Duct Tape

Staple Hammer and Staples

Utility Knife

Ladder

Insulation Blowing Machine (Available at your local rental store)

I've found blowing insulation into the attic is a simple process. Start and the far ends of the attic. Going back and forth make sure its level and smooth. Make sure to get all areas of the attic and don't fill any vents or recessed light areas. Take a tape measure with you and check the levels once in a while. As an example, if your installing an R-38 of fiberglass insulation you would want it to measure 16 inches deep. As you work your way back near the attic access make sure your helper is getting that excess hose out of the way. When you get to about 6 feet from the access hole stop the machine so you can get on the ladder. Once on the ladder finish installing, making sure to bring the level evenly against the dam you previously built.

The final step is to place a piece of batt insulation in the access hole and carefully put the attic hole lid back into place. Now your done! Stay out of that attic as much as possible from this point as loose fill insulation that has been stepped on or crushed looses it's R value.

The Benefits of Using Spray Foam As a Home Insulator

Movement of air in and out of a home can be a leading cause of escalated energy bills. Air can enter your house through holes, cracks and crevices. You can stop unconditioned air from entering your home and indoor conditioned air from escaping outside by adding an advanced insulation system to achieve optimal building performance.

Best Way To Insulate House Walls

An energy efficient home is an environmentally sound home and to achieve energy efficiency insulation is vital. It must be used liberally, and it must be properly installed. There are all sorts of insulating materials, and their green credentials may vary.

The most common is Pink fiberglass Batts which are by no means the worst from an environmental perspective but they aren't the best either. Fiberglass itself is chemically inert, but the glues and backing materials that provide structure to the batts can release dangerous fumes and there is some concern that minute particles of fiberglass can filter into living spaces, presenting a health risk. Rigid polystyrene panels, another popular choice, are made from petrochemicals which are flammable and emit toxic fumes when burned.

Misconceptions about Cellulose:

1: Prone to mold and insects; Cellulose Fiber is treated with two non-irritant, non-toxic, safe to handle allergy free agents; Borax and Boric acid which make it vermin resistant.

2: Fire retardant chemicals disappear in 5 years; The most exhaustive study and technical literature review concluded it would take 300 years to do so and only under continuous harsh conditions of 100% relative humidity and 70 degrees Celsius.

For information on environmentally friendly cellulose, go to www.premiuminstallation.com.au.


http://cozyguyyz.pro/scarborough/

Ceiling Insulation Companies Services By CozyGuYYZ