Most of the energy costs spent to keep a West Hill home warm in the winter and cool in the summer end up leaving through the attic. In the summer, the sun’s heat pours in through the attic and in the winter, warm air rises past the ceiling and out of the home. Saving on energy costs starts in the attic, but how much insulation is enough?
Are You Trying To Find Cavity Wall Insulation Companies For Your West Hill House?
Although spray foam insulation as we know it today truly emerged in the 1980s around the West Hill area, spray foam actually has its roots several decades further in the past, beginning with the development of polyurethane foam in the 1940s by Otto Bayer. Otto Bayer, an industrial chemist, actually began working with polyurethane in Germany during the late 1930s. This technology was brought to the United States in the early 1940s by David Eynon, the president of Mobay, a war effort conglomerate created from the partnering of two chemical industry giants, Monsanto and the Bayer Corporation.
All About Spray Foam Insulation
I have just completed an addition to my house. I've heard that blown in insulation is better than batts since covers the joists completely and leaves no open areas. Do you have any do it yourself suggestions?
Yes you are correct. Blown in insulation is better that batts when installed properly as it does seal the attic better.
First you need to measure your attic area that you plan on insulating. Most attics require a value of R-30, R-38 or R-49, depending on your climate and location. Once you know the square footage of your attic you can determine how much insulation you'll need by simple looking on the chart located on the bag of insulation.
Before you get started you will need to determine what materials you will need. Assuming your home has recessed lights, ceiling and bathroom fans and eave vents you will need the following tools and materials:
Loose Fill Insulation
Staple Hammer and Staples
Insulation Blowing Machine (Available at your local rental store)
I've found blowing insulation into the attic is a simple process. Start and the far ends of the attic. Going back and forth make sure its level and smooth. Make sure to get all areas of the attic and don't fill any vents or recessed light areas. Take a tape measure with you and check the levels once in a while. As an example, if your installing an R-38 of fiberglass insulation you would want it to measure 16 inches deep. As you work your way back near the attic access make sure your helper is getting that excess hose out of the way. When you get to about 6 feet from the access hole stop the machine so you can get on the ladder. Once on the ladder finish installing, making sure to bring the level evenly against the dam you previously built.
The final step is to place a piece of batt insulation in the access hole and carefully put the attic hole lid back into place. Now your done! Stay out of that attic as much as possible from this point as loose fill insulation that has been stepped on or crushed looses it's R value.
Home Insulation Tips: Reflective Foil Insulation
Movement of air in and out of a home can be a leading cause of escalated energy bills. Air can enter your house through holes, cracks and crevices. You can stop unconditioned air from entering your home and indoor conditioned air from escaping outside by adding an advanced insulation system to achieve optimal building performance.
A small science lesson about insulation:
Heat moves from warmer areas to colder areas. This is the single basic principle on which the idea of insulation is based. On hot days heat tries to get inside your house and on cold days the heat tries to escape. Insulation seeks to minimise this ebb and flow of temperature by slowing the process.
Unfortunately no matter how good your home insulation is, any building always needs a constant supply from a heat generating source to maintain a steady temperature. Of course however, if you have good insulation then you will need much less heat and thus a lot less energy to achieve the same effect.
Most of us learned in GCSE science about conduction convection and radiation.
Here is a brief summary of each to refresh every ones memory.
o Distance between surfaces
o The emissive of the surfaces (shiny and light/matt and dark)
o Temperature differences between receiving and radiating surfaces
The application of thermal insulation does not have the effect of generating heat in your house. It is still always the rule that you will have to supply heat from an inside source. There may be a rise in temperature inside the building after the installation of insulation but that will be down to the better performance and energy saving properties of better house insulation.