The main area of a home in Brampton that can let in air from outside into your home is your attic. This is also the main place where insects and animals can infest without you noticing before it is too late. The best to prevent both of these problems is to have the proper sealing done in your attic. This will mainly involve insulating the entire area properly with the most advanced method of insulation that is available right now. The following is the best option of insulation for any type house that has an attic:
CozyGuYYZ: Professional Radiant Barrier Insulation Contractor In Brampton
Foam insulation is a new type of insulation being used a lot in Brampton that many builders and homeowners alike are beginning to use in replacement of lay-in insulation. Instead of stapling pieces of fiberglass-based traditional insulation, this type is completely sprayed onto the area which guarantees complete coverage. This is also very helpful when it comes to tight spaces that are hard to get to.
All About Spray Foam Insulation
A small science lesson about insulation:
Heat moves from warmer areas to colder areas. This is the single basic principle on which the idea of insulation is based. On hot days heat tries to get inside your house and on cold days the heat tries to escape. Insulation seeks to minimise this ebb and flow of temperature by slowing the process.
Unfortunately no matter how good your home insulation is, any building always needs a constant supply from a heat generating source to maintain a steady temperature. Of course however, if you have good insulation then you will need much less heat and thus a lot less energy to achieve the same effect.
Most of us learned in GCSE science about conduction convection and radiation.
Here is a brief summary of each to refresh every ones memory.
o Distance between surfaces
o The emissive of the surfaces (shiny and light/matt and dark)
o Temperature differences between receiving and radiating surfaces
The application of thermal insulation does not have the effect of generating heat in your house. It is still always the rule that you will have to supply heat from an inside source. There may be a rise in temperature inside the building after the installation of insulation but that will be down to the better performance and energy saving properties of better house insulation.
Is Spray on Foam Insulation Worth the Extra Cost?
I have just completed an addition to my house. I've heard that blown in insulation is better than batts since covers the joists completely and leaves no open areas. Do you have any do it yourself suggestions?
Yes you are correct. Blown in insulation is better that batts when installed properly as it does seal the attic better.
First you need to measure your attic area that you plan on insulating. Most attics require a value of R-30, R-38 or R-49, depending on your climate and location. Once you know the square footage of your attic you can determine how much insulation you'll need by simple looking on the chart located on the bag of insulation.
Before you get started you will need to determine what materials you will need. Assuming your home has recessed lights, ceiling and bathroom fans and eave vents you will need the following tools and materials:
Loose Fill Insulation
Staple Hammer and Staples
Insulation Blowing Machine (Available at your local rental store)
I've found blowing insulation into the attic is a simple process. Start and the far ends of the attic. Going back and forth make sure its level and smooth. Make sure to get all areas of the attic and don't fill any vents or recessed light areas. Take a tape measure with you and check the levels once in a while. As an example, if your installing an R-38 of fiberglass insulation you would want it to measure 16 inches deep. As you work your way back near the attic access make sure your helper is getting that excess hose out of the way. When you get to about 6 feet from the access hole stop the machine so you can get on the ladder. Once on the ladder finish installing, making sure to bring the level evenly against the dam you previously built.
The final step is to place a piece of batt insulation in the access hole and carefully put the attic hole lid back into place. Now your done! Stay out of that attic as much as possible from this point as loose fill insulation that has been stepped on or crushed looses it's R value.
- Basement Insulation Contractor Brampton, Ontario |
- Garage Insulation Company Bramalea, Ontario |
- Home Insulation Contractors Churchville, Ontario |