Vaughan Exterior Wall Insulation Contractor

The main area of a home in Vaughan  that can let in air from outside into your home is your attic. This is also the main place where insects and animals can infest without you noticing before it is too late. The best to prevent both of these problems is to have the proper sealing done in your attic. This will mainly involve insulating the entire area properly with the most advanced method of insulation that is available right now. The following is the best option of insulation for any type house that has an attic:

Garage Ceiling Insulation

CozyGuYYZ: Professional Garage Insulation Contractors In Vaughan

Foam insulation is a new type of insulation being used a lot in Vaughan  that many builders and homeowners alike are beginning to use in replacement of lay-in insulation. Instead of stapling pieces of fiberglass-based traditional insulation, this type is completely sprayed onto the area which guarantees complete coverage. This is also very helpful when it comes to tight spaces that are hard to get to.

Icynene Insulation

Proper Attic Insulation

A number of companies are offering DIY polyurethane foam insulation kits for home use. TigerFoam, Handi Foam from FomoFoam, Foam It Green DIY Kits are some of the top brands available online. Tiger Foam offers both Slow Rise and Fast Rise formulations. The Slow Rise is for filling wall cavities and other hidden closed-off spaces in the house. The Fast Rise foam is more suitable for spraying surfaces.

The DIY kits come complete with all the equipment needed to apply the spray foam-nozzles, tank, hose and tips. They also have careful step-by-step instructions that need to be followed in order to the job safely and also for best results.

Apart from insulation the polyurethane foam also acts as a sound barrier. It is moisture resistant and hence prevents mold in the wall cavities and wall surfaces. The excellent insulation capacity of the foam results in the complete cut-off of air transfer from and into the house. Retention of temperature of the house is excellent in homes insulated using polyurethane foam insulation kits. You will save a ton of money in utility bills and the insulation costs will soon paid for.

How Much Attic Insulation is Enough?

Garage Ceiling Insulation

Scenario:

I have just completed an addition to my house. I've heard that blown in insulation is better than batts since covers the joists completely and leaves no open areas. Do you have any do it yourself suggestions?

Solution:

Yes you are correct. Blown in insulation is better that batts when installed properly as it does seal the attic better.

First you need to measure your attic area that you plan on insulating. Most attics require a value of R-30, R-38 or R-49, depending on your climate and location. Once you know the square footage of your attic you can determine how much insulation you'll need by simple looking on the chart located on the bag of insulation.

Before you get started you will need to determine what materials you will need. Assuming your home has recessed lights, ceiling and bathroom fans and eave vents you will need the following tools and materials:

Loose Fill Insulation

Cardboard Baffles

Flashing

Duct Tape

Staple Hammer and Staples

Utility Knife

Ladder

Insulation Blowing Machine (Available at your local rental store)

I've found blowing insulation into the attic is a simple process. Start and the far ends of the attic. Going back and forth make sure its level and smooth. Make sure to get all areas of the attic and don't fill any vents or recessed light areas. Take a tape measure with you and check the levels once in a while. As an example, if your installing an R-38 of fiberglass insulation you would want it to measure 16 inches deep. As you work your way back near the attic access make sure your helper is getting that excess hose out of the way. When you get to about 6 feet from the access hole stop the machine so you can get on the ladder. Once on the ladder finish installing, making sure to bring the level evenly against the dam you previously built.

The final step is to place a piece of batt insulation in the access hole and carefully put the attic hole lid back into place. Now your done! Stay out of that attic as much as possible from this point as loose fill insulation that has been stepped on or crushed looses it's R value.

 


HomePage